Copyright (c) 1992-2007 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-CURRENT #0: Thu Oct 18 22:41:48 PDT 2007 root@obi-wan.spinnaker.com:/usr/obj/usr/src/sys/GENERIC WARNING: WITNESS option enabled, expect reduced performance. Preloaded elf kernel "/boot/kernel/kernel" at 0xc0dce000. Preloaded elf module "/boot/kernel/if_iwi.ko" at 0xc0dce16c. Preloaded elf module "/boot/kernel/sound.ko" at 0xc0dce218. Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc0dce2c4. Preloaded elf module "/boot/kernel/snd_uaudio.ko" at 0xc0dce370. Preloaded elf module "/boot/kernel/iwi_bss.ko" at 0xc0dce420. Calibrating clock(s) ... i8254 clock: 1193169 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 1862011852 Hz CPU: Intel(R) Pentium(R) M processor 1.86GHz (1862.01-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8 Features=0xafe9f9ff Features2=0x180 Instruction TLB: 4 KB Pages, 4-way set associative, 128 entries Data TLB: 4 KB Pages, 4-way set associative, 128 entries Instruction TLB: 4 MB pages, fully associative, 2 entries 2nd-level cache: 2-MB, 8-way set associative, 64-byte line size 1st-level instruction cache: 32 KB, 8-way set associative, 64 byte line size Data TLB: 4 MB Pages, 4-way set associative, 8 entries 1st-level data cache: 32 KB, 8-way set associative, 64 byte line size L2 cache: 2048 kbytes, 8-way associative, 64 bytes/line real memory = 1073606656 (1023 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000001028000 - 0x000000003ed96fff, 1037496320 bytes (253295 pages) avail memory = 1037000704 (988 MB) bios32: Found BIOS32 Service Directory header at 0xc00e6050 bios32: Entry = 0xea8e0 (c00ea8e0) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xe6000+0x48f4 pnpbios: Found PnP BIOS data at 0xc00ff020 pnpbios: Entry = eb000:3d78 Rev = 1.0 pnpbios: Event flag at eb01e pnpbios: OEM ID 8224744e Other BIOS signatures found: snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024] feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_buffersize=16384 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25 ath_rate: version 1.2 wlan_amrr: wlan: <802.11 Link Layer> firmware: 'iwi_bss' version 300: 191142 bytes loaded at 0xc0d9d000 random: nfslock: pseudo-device kbd: new array size 4 kbd1 at kbdmux0 mem: Pentium Pro MTRR support enabled io: null: ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) rr232x: RocketRAID 232x controller driver v1.02 (Oct 18 2007 22:41:28) npx0: INT 16 interface cpu0 on motherboard est0: on cpu0 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 6120e2906000e29 device_attach: est0 attach returned 6 p4tcc0: on cpu0 pci_open(1): mode 1 addr port (0x0cf8) is 0x8000fa04 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25908086) pcibios: BIOS version 2.10 pcib0: pcibus 0 on motherboard pir0: on motherboard $PIR: Links after initial probe: Link IRQ Rtd Ref IRQs 0x60 255 N 10 5 9 10 11 0x61 255 N 8 5 9 10 11 0x62 255 N 9 5 9 10 11 0x63 255 N 9 5 9 10 11 0x6b 255 N 1 5 9 10 11 0x68 255 N 2 5 9 10 11 0x6a 255 N 1 5 9 10 11 $PIR: Found matching pin for 0.1.INTA at func 0: 11 $PIR: Found matching pin for 0.28.INTA at func 0: 10 $PIR: Found matching pin for 0.28.INTB at func 1: 11 $PIR: Found matching pin for 0.29.INTA at func 0: 11 $PIR: Found matching pin for 0.29.INTB at func 1: 11 $PIR: Found matching pin for 0.29.INTC at func 2: 11 $PIR: Found matching pin for 0.29.INTD at func 3: 11 $PIR: Found matching pin for 0.30.INTA at func 2: 10 $PIR: Found matching pin for 0.30.INTB at func 3: 5 $PIR: Found matching pin for 0.31.INTB at func 2: 255 $PIR: Found matching pin for 1.0.INTA at func 0: 11 $PIR: Found matching pin for 2.0.INTA at func 0: 11 $PIR: Found matching pin for 6.4.INTA at func 0: 11 $PIR: Found matching pin for 6.6.INTA at func 0: 255 $PIR: Found matching pin for 6.6.INTA at func 4: 11 $PIR: Found matching pin for 6.6.INTC at func 2: 11 $PIR: Found matching pin for 6.6.INTD at func 3: 5 $PIR: Links after initial IRQ discovery: Link IRQ Rtd Ref IRQs 0x60 11 Y 10 5 9 10 11 0x61 10 Y 8 5 9 10 11 0x62 11 Y 9 5 9 10 11 0x63 11 Y 9 5 9 10 11 0x6b 11 Y 1 5 9 10 11 0x68 5 Y 2 5 9 10 11 0x6a 11 Y 1 5 9 10 11 $PIR: IRQs used by BIOS: 5 10 11 $PIR: Interrupt Weights: [ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ] [ 0 0 0 0 0 2 0 0 0 0 8 30 0 0 0 0 ] pci0: on pcib0 pci0: domain=0, physical bus=0 found-> vendor=0x8086, dev=0x2590, revid=0x03 domain=0, bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2591, revid=0x03 domain=0, bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0007, statreg=0x0010, cachelnsz=4 (dwords) lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 1 message $PIR: 0:1 INTA routed to irq 11 found-> vendor=0x8086, dev=0x2660, revid=0x04 domain=0, bus=0, slot=28, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0007, statreg=0x0010, cachelnsz=4 (dwords) lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 MSI supports 1 message $PIR: 0:28 INTA routed to irq 10 found-> vendor=0x8086, dev=0x2662, revid=0x04 domain=0, bus=0, slot=28, func=1 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0007, statreg=0x0010, cachelnsz=4 (dwords) lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 1 message $PIR: 0:28 INTB routed to irq 11 found-> vendor=0x8086, dev=0x2658, revid=0x04 domain=0, bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 map[20]: type I/O Port, range 32, base 0x1200, size 5, enabled $PIR: 0:29 INTA routed to irq 11 found-> vendor=0x8086, dev=0x2659, revid=0x04 domain=0, bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 map[20]: type I/O Port, range 32, base 0x1220, size 5, enabled $PIR: 0:29 INTB routed to irq 11 found-> vendor=0x8086, dev=0x265a, revid=0x04 domain=0, bus=0, slot=29, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=11 map[20]: type I/O Port, range 32, base 0x1240, size 5, enabled $PIR: 0:29 INTC routed to irq 11 found-> vendor=0x8086, dev=0x265b, revid=0x04 domain=0, bus=0, slot=29, func=3 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=11 map[20]: type I/O Port, range 32, base 0x1260, size 5, enabled $PIR: 0:29 INTD routed to irq 11 found-> vendor=0x8086, dev=0x265c, revid=0x04 domain=0, bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 map[10]: type Memory, range 32, base 0xf4000000, size 10, memory disabled $PIR: 0:29 INTA routed to irq 11 found-> vendor=0x8086, dev=0x2448, revid=0xd4 domain=0, bus=0, slot=30, func=0 class=06-04-01, hdrtype=0x01, mfdev=1 cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x266e, revid=0x04 domain=0, bus=0, slot=30, func=2 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type I/O Port, range 32, base 0xe000, size 8, enabled map[14]: type I/O Port, range 32, base 0xe100, size 6, enabled map[18]: type Memory, range 32, base 0xd0000000, size 9, enabled map[1c]: type Memory, range 32, base 0xd0000200, size 8, enabled $PIR: 0:30 INTA routed to irq 10 found-> vendor=0x8086, dev=0x266d, revid=0x04 domain=0, bus=0, slot=30, func=3 class=07-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=5 powerspec 2 supports D0 D3 current D0 map[10]: type I/O Port, range 32, base 0xe200, size 8, enabled map[14]: type I/O Port, range 32, base 0xe300, size 7, enabled $PIR: 0:30 INTB routed to irq 5 found-> vendor=0x8086, dev=0x2641, revid=0x04 domain=0, bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2653, revid=0x04 domain=0, bus=0, slot=31, func=2 class=01-01-80, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x02b8, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=255 powerspec 2 supports D0 D3 current D0 map[20]: type I/O Port, range 32, base 0x1100, size 4, enabled pcib1: irq 11 at device 1.0 on pci0 pcib1: domain 0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xc000-0xdfff pcib1: memory decode 0xc0000000-0xcfffffff pcib1: prefetched decode 0x90000000-0x9fffffff pci1: on pcib1 pci1: domain=0, physical bus=1 found-> vendor=0x10de, dev=0x0148, revid=0xa2 domain=0, bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0010, cachelnsz=4 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type Memory, range 32, base 0xc0000000, size 26, enabled pcib1: requested memory range 0xc0000000-0xc3ffffff: good map[14]: type Prefetchable Memory, range 64, base 0x90000000, size 27, enabled pcib1: requested memory range 0x90000000-0x97ffffff: good map[1c]: type Memory, range 64, base 0xc1000000, size 24, enabled pcib1: requested memory range 0xc1000000-0xc1ffffff: good $PIR: 1:0 INTA routed to irq 11 vgapci0: mem 0xc0000000-0xc3ffffff,0x90000000-0x97ffffff,0xc1000000-0xc1ffffff irq 11 at device 0.0 on pci1 pcib2: irq 10 at device 28.0 on pci0 pcib2: domain 0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xa000-0xbfff pcib2: memory decode 0xbc000000-0xbfffffff pcib2: prefetched decode 0x8c000000-0x8fffffff pci2: on pcib2 pci2: domain=0, physical bus=2 found-> vendor=0x11ab, dev=0x4351, revid=0x10 domain=0, bus=2, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0010, cachelnsz=4 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 MSI supports 2 messages, 64 bit map[10]: type Memory, range 64, base 0xbc000000, size 14, enabled pcib2: requested memory range 0xbc000000-0xbc003fff: good map[18]: type I/O Port, range 32, base 0xa000, size 8, enabled pcib2: requested I/O range 0xa000-0xa0ff: in range $PIR: 2:0 INTA routed to irq 11 mskc0: port 0xa000-0xa0ff mem 0xbc000000-0xbc003fff irq 11 at device 0.0 on pci2 mskc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xbc000000 mskc0: MSI count : 2 mskc0: attempting to allocate 2 MSI vectors (2 supported) mskc0: RAM buffer size : 16KB mskc0: Port 0 : Rx Queue 10KB(0x00000000:0x000027ff) mskc0: Port 0 : Tx Queue 10KB(0x00002800:0x00004fff) msk0: on mskc0 msk0: bpf attached msk0: Ethernet address: 00:a0:d1:20:b1:b1 miibus0: on msk0 e1000phy0: PHY 0 on miibus0 e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto ukphy0: PHY 2 on miibus0 ukphy0: OUI 0x020002, model 0x0000, rev. 0 ukphy0: 10baseT ukphy1: PHY 3 on miibus0 ukphy1: OUI 0x021002, model 0x0004, rev. 0 ukphy1: 10baseT ukphy2: PHY 4 on miibus0 ukphy2: OUI 0x020002, model 0x0000, rev. 0 ukphy2: 10baseT ukphy3: PHY 5 on miibus0 ukphy3: OUI 0x020002, model 0x0000, rev. 0 ukphy3: 10baseT ukphy4: PHY 6 on miibus0 ukphy4: OUI 0x024402, model 0x0011, rev. 0 ukphy4: 10baseT ukphy5: PHY 7 on miibus0 ukphy5: OUI 0x020002, model 0x0000, rev. 0 ukphy5: 10baseT mskc0: [MPSAFE] mskc0: [FILTER] pcib3: irq 11 at device 28.1 on pci0 pcib3: domain 0 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0x8000-0x9fff pcib3: memory decode 0xb8000000-0xbbffffff pcib3: prefetched decode 0x88000000-0x8bffffff pci3: on pcib3 pci3: domain=0, physical bus=3 uhci0: port 0x1200-0x121f irq 11 at device 29.0 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1200 uhci0: [GIANT-LOCKED] uhci0: [ITHREAD] usb0: on uhci0 usb0: USB revision 1.0 uhub0: on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: port 0x1220-0x123f irq 11 at device 29.1 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1220 uhci1: [GIANT-LOCKED] uhci1: [ITHREAD] usb1: on uhci1 usb1: USB revision 1.0 uhub1: on usb1 uhub1: 2 ports with 2 removable, self powered uhci2: port 0x1240-0x125f irq 11 at device 29.2 on pci0 uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1240 uhci2: [GIANT-LOCKED] uhci2: [ITHREAD] usb2: on uhci2 usb2: USB revision 1.0 uhub2: on usb2 uhub2: 2 ports with 2 removable, self powered uhci3: port 0x1260-0x127f irq 11 at device 29.3 on pci0 uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1260 uhci3: [GIANT-LOCKED] uhci3: [ITHREAD] usb3: on uhci3 usb3: USB revision 1.0 uhub3: on usb3 uhub3: 2 ports with 2 removable, self powered ehci0: mem 0xf4000000-0xf40003ff irq 11 at device 29.7 on pci0 ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xf4000000 ehci0: [GIANT-LOCKED] ehci0: [ITHREAD] usb4: EHCI version 1.0 usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4: on ehci0 usb4: USB revision 2.0 uhub4: on usb4 uhub4: 8 ports with 8 removable, self powered pcib4: at device 30.0 on pci0 pcib4: domain 0 pcib4: secondary bus 6 pcib4: subordinate bus 6 pcib4: I/O decode 0x6000-0x7fff pcib4: memory decode 0xb0000000-0xb7ffffff pcib4: prefetched decode 0x80000000-0x87ffffff pcib4: Subtractively decoded bridge. pci6: on pcib4 pci6: domain=0, physical bus=6 found-> vendor=0x8086, dev=0x4223, revid=0x05 domain=0, bus=6, slot=4, func=0 class=02-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x80 (3840 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 map[10]: type Memory, range 32, base 0xb000b000, size 12, enabled pcib4: requested memory range 0xb000b000-0xb000bfff: good $PIR: 6:4 INTA routed to irq 11 found-> vendor=0x104c, dev=0x8031, revid=0x00 domain=0, bus=6, slot=6, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0xc0 (48000 ns), maxlat=0x03 (750 ns) intpin=a, irq=255 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0x13000000, size 12, enabled pcib4: requested memory range 0x13000000-0x13000fff: good found-> vendor=0x104c, dev=0x8032, revid=0x00 domain=0, bus=6, slot=6, func=2 class=0c-00-10, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0210, cachelnsz=4 (dwords) lattimer=0x80 (3840 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns) intpin=c, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xb0000000, size 11, enabled pcib4: requested memory range 0xb0000000-0xb00007ff: good map[14]: type Memory, range 32, base 0xb0004000, size 14, enabled pcib4: requested memory range 0xb0004000-0xb0007fff: good $PIR: 6:6 INTC routed to irq 11 found-> vendor=0x104c, dev=0x8033, revid=0x00 domain=0, bus=6, slot=6, func=3 class=01-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0210, cachelnsz=4 (dwords) lattimer=0x80 (3840 ns), mingnt=0x07 (1750 ns), maxlat=0x04 (1000 ns) intpin=d, irq=5 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xb0008000, size 13, enabled pcib4: requested memory range 0xb0008000-0xb0009fff: good $PIR: 6:6 INTD routed to irq 5 found-> vendor=0x104c, dev=0x8034, revid=0x00 domain=0, bus=6, slot=6, func=4 class=08-05-00, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0210, cachelnsz=4 (dwords) lattimer=0x80 (3840 ns), mingnt=0x07 (1750 ns), maxlat=0x04 (1000 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xb000a000, size 8, enabled pcib4: requested memory range 0xb000a000-0xb000a0ff: good map[14]: type Memory, range 32, base 0xb000a100, size 8, enabled pcib4: requested memory range 0xb000a100-0xb000a1ff: good map[18]: type Memory, range 32, base 0xb000a200, size 8, enabled pcib4: requested memory range 0xb000a200-0xb000a2ff: good $PIR: 6:6 INTA routed to irq 11 iwi0: mem 0xb000b000-0xb000bfff irq 11 at device 4.0 on pci6 iwi0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xb000b000 iwi0: bpf attached iwi0: Ethernet address: 00:12:f0:89:f6:4b iwi0: bpf attached iwi0: bpf attached iwi0: [MPSAFE] iwi0: [ITHREAD] iwi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps iwi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps iwi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps cbb0: mem 0x13000000-0x13000fff at device 6.0 on pci6 pcib4: cbb0 requested memory range 0x13000000-0x13000fff: good cbb0: Could not map register memory device_attach: cbb0 attach returned 12 fwohci0: vendor=104c, dev=8032 fwohci0: vendor=104c, dev=8032 fwohci0: <1394 Open Host Controller Interface> mem 0xb0000000-0xb00007ff,0xb0004000-0xb0007fff irq 11 at device 6.2 on pci6 fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xb0000000 fwohci0: [MPSAFE] fwohci0: [FILTER] fwohci0: OHCI version 1.10 (ROM=0) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:08:0d:a0:d1:20:b1:b1 fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: on fwohci0 dcons_crom0: on firewire0 dcons_crom0: bus_addr 0x1374000 fwe0: on firewire0 if_fwe0: Fake Ethernet address: 02:08:0d:20:b1:b1 fwe0: bpf attached fwe0: Ethernet address: 02:08:0d:20:b1:b1 fwip0: on firewire0 fwip0: bpf attached fwip0: Firewire address: 00:08:0d:a0:d1:20:b1:b1 @ 0xfffe00000000, S400, maxrec 2048 sbp0: on firewire0 fwohci0: Initiate bus reset fwohci0: BUS reset fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode pci6: at device 6.3 (no driver attached) pci6: at device 6.4 (no driver attached) pcm0: port 0xe000-0xe0ff,0xe100-0xe13f mem 0xd0000000-0xd00001ff,0xd0000200-0xd00002ff irq 10 at device 30.2 on pci0 pcm0: Reserved 0x200 bytes for rid 0x18 type 3 at 0xd0000000 pcm0: Reserved 0x100 bytes for rid 0x1c type 3 at 0xd0000200 pcm0: [MPSAFE] pcm0: [ITHREAD] pcm0: pcm0: Codec features headphone, 20 bit DAC, 5 bit master volume, no 3D Stereo Enhancement pcm0: Primary codec extended features variable rate PCM, AMAP, reserved 4 pcm0: ac97 codec dac ready count: 0 pcm0: Mixer "vol": pcm0: Mixer "pcm": pcm0: Mixer "line": pcm0: Mixer "mic": pcm0: Mixer "cd": pcm0: Mixer "rec": pcm0: Mixer "igain": pcm0: Mixer "ogain": pcm0: Mixer "line1": pcm0: Mixer "phin": pcm0: Mixer "phout": pcm0: clone manager: deadline=750ms flags=0x8000001e pcm0: sndbuf_setmap 1754000, 4000; 0xe4994000 -> 1754000 pcm0: sndbuf_setmap 175c000, 4000; 0xe4998000 -> 175c000 pci0: at device 30.3 (no driver attached) isab0: at device 31.0 on pci0 isa0: on isab0 atapci0: port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1100-0x110f at device 31.2 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1100 ata0: on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=50 stat1=00 devices=0x1 ata0: [MPSAFE] ata0: [ITHREAD] ata1: on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=50 ostat1=00 ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb ata1: stat1=0x00 err=0x00 lsb=0x00 msb=0x00 ata1: reset tp2 stat0=00 stat1=00 devices=0x4 ata1: [MPSAFE] ata1: [ITHREAD] unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff ex_isa_identify() ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it pnp_identify: Trying Read_Port at 203 pnp_identify: Trying Read_Port at 243 pnp_identify: Trying Read_Port at 283 pnp_identify: Trying Read_Port at 2c3 pnp_identify: Trying Read_Port at 303 pnp_identify: Trying Read_Port at 343 pnp_identify: Trying Read_Port at 383 pnp_identify: Trying Read_Port at 3c3 PNP Identify complete pnpbios: 16 devices, largest 230 bytes PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000 PNP0c01: adding fixed memory32 range 0x100000-0x3ffeffff, size=0x3fef0000 PNP0c01: adding fixed memory32 range 0xe0000-0xfffff, size=0x20000 PNP0c01: adding fixed memory32 range 0xcf000-0xcffff, size=0x1000 PNP0c01: adding fixed memory32 range 0xfff80000-0xffffffff, size=0x80000 pnpbios: handle 0 device ID PNP0c01 (010cd041) PNP0c02: adding io range 0x4d0-0x4d1, size=0x2, align=0 PNP0c02: adding io range 0x680-0x6ff, size=0x80, align=0 PNP0c02: adding io range 0x92-0x92, size=0x1, align=0 PNP0c02: adding io range 0x62-0x62, size=0x1, align=0 PNP0c02: adding io range 0x66-0x66, size=0x1, align=0 PNP0c02: adding io range 0x2e-0x2f, size=0x2, align=0 PNP0c02: adding io range 0xb2-0xb3, size=0x2, align=0 PNP0c02: adding io range 0x1000-0x107f, size=0x80, align=0 PNP0c02: adding io range 0x1300-0x133f, size=0x40, align=0 pnpbios: handle 1 device ID PNP0c02 (020cd041) PNP0c04: adding irq mask 0x2000 PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0 pnpbios: handle 2 device ID PNP0c04 (040cd041) PNP0200: adding io range 0-0x1f, size=0x20, align=0 PNP0200: adding io range 0x80-0x8f, size=0x10, align=0 PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0 PNP0200: adding dma mask 0x10 pnpbios: handle 4 device ID PNP0200 (0002d041) PNP0100: adding irq mask 0x1 PNP0100: adding io range 0x40-0x5f, size=0x20, align=0 pnpbios: handle 5 device ID PNP0100 (0001d041) PNP0b00: adding irq mask 0x100 PNP0b00: adding io range 0x70-0x7f, size=0x10, align=0 pnpbios: handle 6 device ID PNP0b00 (000bd041) PNP0303: adding irq mask 0x2 PNP0303: adding io range 0x60-0x60, size=0x1, align=0 PNP0303: adding io range 0x64-0x64, size=0x1, align=0 pnpbios: handle 7 device ID PNP0303 (0303d041) PNP0800: adding io range 0x61-0x61, size=0x1, align=0 pnpbios: handle 8 device ID PNP0800 (0008d041) PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0 pnpbios: handle 9 device ID PNP0a03 (030ad041) PNP0f13: adding irq mask 0x1000 pnpbios: handle 10 device ID PNP0f13 (130fd041) INT0800: adding fixed memory32 range 0xffb00000-0xffb7ffff, size=0x80000 pnpbios: handle 11 device ID INT0800 (0008d425) PNP0501: adding irq mask 0x10 PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0 pnpbios: handle 13 device ID PNP0501 (0105d041) PNP0e03: adding io range 0x3e0-0x3e3, size=0x4, align=0 pnpbios: handle 15 device ID PNP0e03 (030ed041) SMCf010: adding irq mask 0x8 SMCf010: adding io range 0x2f8-0x2ff, size=0x8, align=0 SMCf010: adding io range 0x110-0x117, size=0x8, align=0 SMCf010: adding dma mask 0x2 pnpbios: handle 16 device ID SMCf010 (10f0a34d) PNP0401: adding irq mask 0x80 PNP0401: adding io range 0x378-0x37f, size=0x8, align=0 PNP0401: adding io range 0x778-0x77b, size=0x4, align=0 PNP0401: adding dma mask 0x8 pnpbios: handle 17 device ID PNP0401 (0104d041) sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices pmtimer0 on isa0 orm0: at iomem 0xc0000-0xcefff,0xe0000-0xe1fff,0xe5000-0xe5fff,0xeb000-0xeffff pnpid ORM0000 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) atkbdc0: at port 0x60,0x64 on isa0 atkbd0: irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0067 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] psm0: current command byte:0067 psm0: irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: [ITHREAD] psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons psm0: config:00000000, flags:00000008, packet size:3 psm0: syncmask:c0, syncbits:00 bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) ppc0: parallel port not found. ppc0: failed to probe at irq 7 on isa0 fb: new array size 4 sc0: at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0x801 0x801 0x801 0x801 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0x801 0x801 0x801 0x801 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding sio0: [FILTER] sio1: irq maps: 0x801 0x809 0x801 0x801 sio1: irq maps: 0x801 0x809 0x801 0x801 sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A sio1: [FILTER] sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 vt0: not probed (disabled) isa_probe_children: probing PnP devices unknown: can't assign resources (memory) unknown: at iomem 0-0x9ffff pnpid PNP0c01 on isa0 unknown: can't assign resources (port) unknown: at port 0x60 pnpid PNP0303 on isa0 unknown: failed to probe at port 0x61 pnpid PNP0800 on isa0 unknown: can't assign resources (irq) unknown: at irq 12 pnpid PNP0f13 on isa0 unknown: failed to probe at iomem 0xffb00000-0xffb7ffff pnpid INT0800 on isa0 unknown: can't assign resources (port) unknown: at port 0x3f8-0x3ff pnpid PNP0501 on isa0 cbb1: at port 0x3e0-0x3e3 irq 5 pnpid PNP0e03 on isa0 device_attach: cbb1 attach returned 12 unknown: can't assign resources (port) unknown: at port 0x2f8-0x2ff pnpid SMCf010 on isa0 ppc1: using extended I/O port range unknown: failed to probe at port 0x378-0x37f,0x778-0x77b irq 7 drq 3 pnpid PNP0401 on isa0 ums0: on uhub0 ums0: 3 buttons and Z dir. Device configuration finished. procfs registered Timecounter "TSC" frequency 1862011852 Hz quality 800 Timecounters tick every 1.000 msec lo0: bpf attached rr232x: no controller dfirewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) etected. ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire ad0: 152627MB at ata0-master UDMA100 ad0: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue GEOM: new disk ad0 ad0: Intel check1 failed ad0: Adaptec check1 failed ad0: LSI (v3) check1 failed ad0: LSI (v2) check1 failed ad0: FreeBSD check1 failed ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire acd0: DVDR drive at ata1 as master acd0: read 4134KB/s (4134KB/s) write 4134KB/s (4134KB/s), 2048KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc GEOM_LABEL: Label for provider ad0s1 is ntfs/WinXP. pcm0: measured ac97 link rate at 48003 Hz, will use 48000 Hz (probe0:sbp0:0:0:0): error 22 (probe0:sbp0:0:0:0): Unretryable Error (probe1:sbp0:0:1:0): error 22 (probe1:sbp0:0:1:0): Unretryable Error (probe2:sbp0:0:2:0): error 22 (probe2:sbp0:0:2:0): Unretryable Error (probe3:sbp0:0:3:0): error 22 (probe3:sbp0:0:3:0): Unretryable Error (probe4:sbp0:0:4:0): error 22 (probe4:sbp0:0:4:0): Unretryable Error (probe6:sbp0:0:6:0): error 22 (probe6:sbp0:0:6:0): Unretryable Error (probe5:sbp0:0:5:0): error 22 (probe5:sbp0:0:5:0): Unretryable Error ATA PseudoRAID loaded WARNING: WITNESS option enabled, expect reduced performance. Trying to mount root from ufs:/dev/ad0s3a start_init: trying /sbin/init mskc0: Uncorrectable PCI Express error Linux ELF exec handler installed msk0: link state changed to UP